| Commit message (Collapse) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| * | Base: Set bridge speed to 100 | Patrick McDermott | 2019-10-19 | 1 | -2/+2 |
| | | |||||
| * | Base: Raise perimeter and solid fill speeds to 100 | Patrick McDermott | 2019-10-19 | 1 | -6/+6 |
| | | |||||
| * | Base: Decrease fill density to 10% | Patrick McDermott | 2019-10-19 | 1 | -2/+2 |
| | | |||||
| * | Base: Disable ineffective infill combination | Patrick McDermott | 2019-10-19 | 1 | -2/+2 |
| | | | | | Doesn't work when infill_every_layers * layer_height == nozzle_diameter. | ||||
| * | Revert "Base: Reduce layer height to 0.2 mm" | Patrick McDermott | 2019-10-18 | 1 | -3/+3 |
| | | | | | | | | | This reverts commit ab84e54274cf87f575ff1436b064ac52df3f9ad9. The higher number of perimeter layers and lower number of infill layers almost balance each other out in print time. Layer seams are similar as well; if anything, the 0.2-mm seams protrude more. | ||||
| * | Base: Reduce layer height to 0.2 mm | Patrick McDermott | 2019-10-18 | 1 | -3/+3 |
| | | | | | Now infill_every_layers is actually effective. | ||||
| * | Base: Raise perimeter and top infill speeds to 80 | Patrick McDermott | 2019-10-18 | 1 | -5/+5 |
| | | |||||
| * | Base: Increase infill to 20% | P. J. McDermott | 2019-02-16 | 1 | -2/+2 |
| | | |||||
| * | Revert "Base: Increase solid infill speed" | P. J. McDermott | 2019-02-16 | 1 | -2/+2 |
| | | | | | | | | This reverts commit 2951372658017c61012b7a845abd0dbeda8bc0ee. Slic3r uses this speed for the bottom solid infill, so at this speed there's insufficient extrusion. | ||||
| * | Base: Increase solid infill speed | P. J. McDermott | 2019-02-16 | 1 | -2/+2 |
| | | |||||
| * | Revert "Revert "Base: Reduce infill overlap to 0"" | P. J. McDermott | 2019-02-15 | 1 | -2/+2 |
| | | | | | This reverts commit 845c4ac12e94c49760f8e9519ab469b816576a12. | ||||
| * | Revert "Base: Reduce infill overlap to 0" | P. J. McDermott | 2019-02-15 | 1 | -2/+2 |
| | | | | | This reverts commit 8c298d81d0463734718be995d9bd838be4f21d67. | ||||
| * | Base: Reduce infill overlap to 0 | P. J. McDermott | 2019-02-15 | 1 | -2/+2 |
| | | |||||
| * | Base: Slow down perimeters, speed up infill | P. J. McDermott | 2019-02-14 | 1 | -8/+8 |
| | | |||||
| * | Base: Infill everywhere | P. J. McDermott | 2019-02-14 | 1 | -2/+2 |
| | | |||||
| * | Revert "Revert "Revert "Base: Increase speeds""" | P. J. McDermott | 2019-02-14 | 1 | -11/+11 |
| | | | | | This reverts commit 0788865c4bf387d862598a0cb5d9fa1d41014f7a. | ||||
| * | Revert "Revert "Base: Increase speeds"" | P. J. McDermott | 2019-02-14 | 1 | -11/+11 |
| | | | | | This reverts commit 184eb929444cd45bc49d6eaf33e00be13a89047d. | ||||
| * | Revert "Base: Increase minimum skirt length" | P. J. McDermott | 2019-02-14 | 1 | -1/+1 |
| | | | | | This reverts commit a34dda7501fb006879f19b1ed9b76fb1f8338b52. | ||||
| * | Revert "Base: Increase speeds" | P. J. McDermott | 2019-02-14 | 1 | -11/+11 |
| | | | | | This reverts commit 305f7215ca937b31a6f1ec54ae928df138196834. | ||||
| * | Base: Increase speeds | P. J. McDermott | 2019-02-14 | 1 | -11/+11 |
| | | |||||
| * | Base: Reduce solid infill threshold area | P. J. McDermott | 2019-02-14 | 1 | -2/+2 |
| | | |||||
| * | Base: Increase minimum skirt length | P. J. McDermott | 2019-02-14 | 1 | -2/+2 |
| | | |||||
| * | Base: Reduce infill/perimeters overlap | P. J. McDermott | 2019-02-14 | 1 | -2/+2 |
| | | |||||
| * | Base: Run 4 threads | P. J. McDermott | 2019-02-14 | 1 | -2/+2 |
| | | |||||
| * | Base: Combine infill and only infill where needed | P. J. McDermott | 2019-02-14 | 1 | -3/+3 |
| | | |||||
| * | Base: Increase speeds | P. J. McDermott | 2019-02-14 | 1 | -8/+8 |
| | | |||||
| * | TAZ 6, SE v2.1, eSUN PLA; Base: Lift on retract, increase travel speed | P. J. McDermott | 2019-02-14 | 1 | -2/+2 |
| | | |||||
| * | Base: Increase travel speed | P. J. McDermott | 2019-02-13 | 1 | -2/+2 |
| | | |||||
| * | Base: New print preset, based on SFF-8201 HA | P. J. McDermott | 2019-02-13 | 1 | -0/+86 |
| | | |||||
| * | print: Slow down perimeter print speeds | P. J. McDermott | 2017-08-21 | 1 | -5/+5 |
| | | | | | | | | | | | Loading two SFF-8201 HAs into Printrun, before: Estimated duration: 11 layers, 0:18:04 Loading two SFF-8201 HAs into Printrun, after: Estimated duration: 11 layers, 0:19:49 | ||||
| * | print: Generate verbose (commented) G-code | P. J. McDermott | 2017-08-21 | 1 | -2/+2 |
| | | |||||
| * | print: Add infill and double print speeds | P. J. McDermott | 2017-08-21 | 1 | -10/+10 |
| | | | | | Also increase skirt distance. | ||||
| * | print: Reduce skirt distanceprint-v2 | P. J. McDermott | 2017-08-21 | 1 | -2/+2 |
| | | | | | | This is done to fit two SFF-8201 HAs with a 4-mm skirt on a LulzBot Mini bed. | ||||
| * | print: Increase all print speeds to 40 mm/s | P. J. McDermott | 2017-08-21 | 1 | -7/+7 |
| | | |||||
| * | print: Reduce perimeters and top/bottom solid layers to 2 | P. J. McDermott | 2017-08-21 | 1 | -4/+4 |
| | | |||||
| * | print: Add new preset | P. J. McDermott | 2017-08-21 | 2 | -18/+86 |
| | | | | | | Use git-log or git-show with `-M13%` to see the changes between the presets. | ||||
| * | Add printer settings | P. J. McDermott | 2016-04-10 | 1 | -0/+18 |
 |
index : dotfiles/slic3r.git | |
| Slic3r configuration | P. J. McDermott |
| summaryrefslogtreecommitdiffstats |