summaryrefslogtreecommitdiffstats
diff options
context:
space:
mode:
-rw-r--r--docs/install/bbb_setup.html472
1 files changed, 432 insertions, 40 deletions
diff --git a/docs/install/bbb_setup.html b/docs/install/bbb_setup.html
index a7d2879..19a8989 100644
--- a/docs/install/bbb_setup.html
+++ b/docs/install/bbb_setup.html
@@ -384,49 +384,440 @@ Note: flashrom can never write if the flash chip isn't found automatically.
</div>
<div class="section">
-
<h1>EHCI debugging</h1>
-
- <p>
- Some libreboot systems lack serial ports, so you have to use the debug port (USB) instead.
- The BeagleBone can be configured for this. It may involve compiling a patched kernel.
- </p>
-
- <p>
- Work is in progress to implement this, and document it in libreboot. These are just some preliminary notes.
- </p>
-
- <p>
- <a href="http://www.coreboot.org/EHCI_Debug_Port">http://www.coreboot.org/EHCI_Debug_Port</a>
- <a href="http://www.coreboot.org/EHCI_Gadget_Debug">http://www.coreboot.org/EHCI_Gadget_Debug</a>
- </p>
-
+ <ol class="toc">
+ <li><a href="#FindUSBportonthetargetthatsupportsEHCIdebug">Find
+ USB port on the target that supports EHCI debug</a></li>
+ <li><a href="#InitialsetupofBBBtoactasEHCIdebugdongle">Initial
+ setup of BBB to act as EHCI debug dongle</a></li>
+ <li><a href="#PatchBBBsgdbgpmoduleoptionalbuthighlyrecommended">Patch
+ BBB's <tt>g_dbgp</tt> module (optional, but highly recommended)</a></li>
+ <li><a href="#ConfigurelibrebootwithEHCIdebug">Configure
+ libreboot with EHCI debug</a>
+ <ol>
+ <li><a href="#SelectingHCDIndexandUSBDebugport">Selecting
+ <tt>HCD Index</tt> and <tt>USB Debug port</tt></a></li>
+ </ol></li>
+ <li><a href="#Howtogetthedebuglogs">How to get the debug
+ logs</a></li>
+ <li><a
+ href="#EnebleEHCIDebugonthetargetskerneloptionalrecommended">Eneble
+ EHCI Debug on the target's kernel (optional, recommended)</a></li>
+ <li><a href="#References">References</a></li>
+ </ol>
+ <p>If your computer does not boot after installing libreboot, it is
+ very useful to get debug logs from it, from the payload (grub) and/or
+ the kernel (if gets to there). All of them stream debug logs on the
+ available serial (RS-232) by default. However, most of todays laptops
+ lack RS-232 port. The other option is to stream the logs to USB EHCI
+ debug port.</p>
+ <p>This section explains step-by-step how to setup BBB as a
+ &#8220;USB EHCI debug dongle&#8221; and configure libreboot and the
+ linux kernel to stream logs to it (TODO: grub).</p>
+ <p>I will refer to three computers:</p>
+ <ul>
+ <li><b>host</b> - this is the computer you use, have
+ tools, compiler, Internet, etc</li>
+ <li><b>BBB</b> - Beaglebone Black (rev. B or higher, i
+ use rev. C)</li>
+ <li><b>target</b> - the computer you are trying to
+ install liberboot</li>
+ </ul>
+ <h3 id="FindUSBportonthetargetthatsupportsEHCIdebug">Find USB port
+ on the target that supports EHCI debug</h3>
+ <p>
+ Not all USB controllers support EHCI debug (see: <a
+ href="http://www.coreboot.org/EHCI_Debug_Port#Hardware_capability">EHCI
+ Debug Port</a> ). Even more, if a USB controller supports EHCI debug, it
+ is available only <b>on a single port</b> that might or might
+ not be exposed externally.
+ </p>
+ <ul>
+ <li>You need running OS (GNU/Linux) on your target for this step
+ (If you&#8217;ve flashed libreboot and it does not boot, you have to
+ flush back the stock bios)</li>
+ <li>You need USB memory stick (the data on it will not be
+ touched).</li>
+ <li>The EHCI debugging can not be done through external hub, BBB
+ must be connected directly to the debug port of the controller (so, no
+ hubs)</li>
+ </ul>
+ <ul>
+ <li>Download<sup class="footnote"><a href="#___fn1">1</a></sup> <a
+ href="http://www.coreboot.org/pipermail/coreboot/attachments/20080909/ae11c291/attachment.sh">this</a>
+ shell script.
+ </li>
+ </ul>
+ <ol>
+ <li>Plug the usb stick in the first available usb port</li>
+ <li>Run the script, you will get output similar to following:</li>
+<pre>The following PCI devices support a USB debug port (says lspci): 0000:00:1a.0 0000:00:1d.0
+The following PCI devices support a USB debug port (says the kernel): 0000:00:1a.0 0000:00:1d.0
+*PCI device 0000:00:1a.0, USB bus 3, USB physical port 1*
+*PCI device 0000:00:1d.0, USB bus 4, USB physical port 2*
+Currently connected high-speed devices:
+/: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
+ |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/8p, 480M
+ |__ Port 7: Dev 14, If 0, Class=Hub, Driver=hub/4p, 480M
+ |__ Port 1: Dev 15, If 0, Class=Hub, Driver=hub/4p, 480M
+ |__ Port 3: Dev 17, If 0, Class=Hub, Driver=hub/2p, 480M
+ |__ Port 4: Dev 18, If 0, Class=Hub, Driver=hub/4p, 480M
+/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
+ |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/6p, 480M
+/: *Bus 01*.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 480M
+ |__ *Port 3: Dev 31, If 0, Class=Mass Storage, Driver=usb-storage, 480M*
+</pre>
+ <li>The buses the support debug are Bus 3 (0000:00:1a.0) on Port 1
+ and Bus 4 (0000:00:1d.0) on port 2. Your usb stick is plugged on Bus
+ 1, Port 3</li>
+ <li>Repeat the steps, plugging the USB stick in the next available
+ port</li>
+ <li>Go through all available ports and remember(write down) those
+ for which bus/port of the usb stick matches one of the bus/port that
+ support debug (bold).</li>
+ </ol>
+ <p>Remember (write down) for each port (external plug) you found
+ that supports debug: <b>PCI device id, the bus id, the port number, and
+ the physical location of the usb plug.</b></p>
+ <p>If you do not find a match, you can not get debug over EHCI.
+ Sorry.</p>
+ <p id="___fn1" class="footnote">
+ <sup>1</sup> The guys from coreboot were talking about including the
+ script in coreboot distribution (check the status).
+ </p>
+ <h3 id="InitialsetupofBBBtoactasEHCIdebugdongle">Initial setup of
+ BBB to act as EHCI debug dongle</h3>
+ <p>BBB must be powered with a barrel power connector since the
+ mini-B USB plug will be used for the EHCI debug stream. So you will
+ need:</p>
+ <ul>
+ <li>power supply (5V, 2A(10W) is sufficient).</li>
+ <li>an extra usb cable: A to mini-B</li>
+ </ul>
+ <p>
+ (On BBB) The linux kernel includes module (g_dbgp that enables one of the usb ports on a computer to behave as EHCI
+ debug dongle. Make sure you have this module available on your BBB
+ (Debian 7.8 that comes with BBB should have it), if not, you should
+ compile it yourself (see next section):
+ </p>
+<pre>ls /lib/modules/3.8.13-bone70/kernel/drivers/usb/gadget/g_dbgp.ko</pre>
+ <p>
+ Unload all other
+ g_*
+ modules:
+ </p>
+<pre># lsmod
+# rmmod g_multi
+...
+</pre>
+ <p>
+ Then load
+ g_dbgp
+ :
+ </p>
+<pre># modprobe g_dbgp
+# lsmod # should show that g_dbgp is loaded, and no other g_*
+</pre>
+ <p>
+ Plug the mini-B side of the USB cable in your BBB and the A side in
+ your target. Then one of the usb devices on your target (with
+ lsusb
+ ) should be:
+ </p>
+<pre>Bus 001 Device 024: ID 0525:c0de Netchip Technology, Inc.</pre>
+ <p>If you see the device on the target, you are good to continue to
+ the next step.</p>
+ <h3 id="PatchBBBsgdbgpmoduleoptionalbuthighlyrecommended">
+ Patch BBB&#8217;s
+ g_dbgp
+ module (optional, but highly recommended)
+ </h3>
+ <p>
+ For the reasons why you need this, see: <a
+ href="http://www.coreboot.org/EHCI_Gadget_Debug">EHCI Gadget Debug</a>.<br />Make
+ sure that you have cross compiling environment for
+ arm-linux-gnueabihf
+ setup on your <em>host</em>.
+ </p>
+ <ul>
+ <li>On BBB: uname -r - this will give you version
+ number like 3.8.13-bone70 (I will refer to this as: $mav.$miv-$lv:
+ where mav=3.8, miv=13, lv=bone70
+ </li>
+ <li>Get the BBB kernel ready on your host for cross-compiling:</li>
+ </ul>
+<pre>$ cd $work_dir
+$ git clone https://github.com/beagleboard/kernel.git
+$ cd kernel
+$ git checkout $mav (see above)
+$ ./patch.sh
+$ wget http://arago-project.org/git/projects/?p=am33x-cm3.git\;a=blob_plain\;f=bin/am335x-pm-firmware.bin\;hb=HEAD -O kernel/firmware/am335x-pm-firmware.bin
+$ cp configs/beaglebone kernel/arch/arm/configs/beaglebone_defconfig
+</pre>
+ <ul>
+ <li>Download the patch from <a
+ href="http://www.coreboot.org/images/8/88/Ehci-debug-gadget-patches.tar.gz">here</a></li>
+ <li>tar -xf Ehci-debug-gadget-patches.tar.gz (will
+ create dir: usbdebug-gadget)</li>
+ <li>Note that there are two patches (patch_1 and patch_2) for each
+ of the two different version of the kernel (3.8 and 3.10). I will use
+ 3.8. (If using kernel 3.12 patch_1 is not needed)</li>
+ <li>cd kernel (note that this is one more level: you
+ should be in $work_dir/kernel/kernel)</li>
+ <li>Apply the patches:</li>
+ </ul>
<pre>
-from #coreboot
-&lt;tty0_&gt; stefanct, 1) plug the the BBB to a running system first and make sure you see it as "Netchip" (with lsusb). if that is correct (i.e you have BBB > ver1 ) , you have to rebuild coreboot/libreboot with Net20DB instead of BBB as debug dongle
-&lt;stefanct&gt; tty0_: the coreboot config is clear to me... it fails to show up in lsusb already
-&lt;tty0_&gt; on BBB, unload all the modules, then modprobe g_dbgp
-&lt;tty0_&gt; ... and when i siad lsusb, you do that on the target system, not on BBB
-
-&lt;tty0_&gt; fchmmr, the kernel should be compiled with: CONFIG_EARLY_PRINTK_DBGP=y to output on EHCI debug: https://wiki.ubuntu.com/Kernel/Debugging/USBearlyprintk
-
-&lt;tty0_&gt; stefanct, carldani: Note that the script has small bug in the last for loop: for dev in &quot;$debug_dmesg_devs&quot;; do ...
-&lt;stefanct&gt; tty0_: had ;)
-&lt;stefanct&gt; carldani: ok that's what i was expecting, thanks
-* ob-sed has quit (Ping timeout: 248 seconds)
-&lt;tty0_&gt; On the wiki there are links to two scripts, the updated one has bug
-&lt;tty0_&gt; $debug_dmesg_devs should not be quoted
-&lt;tty0_&gt; ... if there are multiple controllers with debug, $dev will be assgined &lt;controller1 controller2&gt; instead of iterating throug each of them
-&lt;stefanct&gt; i have seen your conversation with mtjm earlier
-&lt;stefanct&gt; that's the reason why i was working on usb debug today at all :)
-&lt;stefanct&gt; idwer: ping
-&lt;carldani&gt; tty0_: indeed, this was a bug.
-&lt;stefanct&gt; carldani: the most annoying thing about lsusb... the debug device is actually missing from lsusb -t as i have found out today
-&lt;tty0_&gt; It shows only ports that have something attached to them, because of that you have to go with usb stick through all the ports and run the script each time
-&lt;stefanct&gt; tty0_: lsusb without the -t shows the debug device... but doesnt print the port number
-
+git apply ../usbdebug-gadget/v3.8-debug-gadget/0001-usb-dbgp-gadget-Fix-re-connecting-after-USB-disconne.patch
+git apply ../usbdebug-gadget/v3.8-debug-gadget/0002-usb-serial-gadget-no-TTY-hangup-on-USB-disconnect-WI.patch
+;
+make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- beaglebone_defconfig -j4@
</pre>
-
+ <ul>
+ <li>Get your current BBB kernel config (from: /boot/config-&lt;ver&gt;)
+ and copy it to your host as $work_dir/kernel/kernel/.config</li>
+<pre>
+make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- oldconfig - all default answers</pre>
+ <li>Set proper version number:
+ <ul>
+ <li>On your host, edit $work_dir/kernel/kernel/.config
+ (the one you&#8217;ve just copied from BBB), find the line CONFIG_LOCALVERSION="&lt;something
+ or empty&gt;" and change it to CONFIG_LOCALVERSION="-$lv",
+ so it will look something like: CONFIG_LOCALVERSION="-bone70"</li>
+ </ul>
+ </li>
+ <li>Also, make sure that: CONFIG_USB_G_DBGP=m (If
+ not, make menuconfig, and set @Device Drivers-&gt; USB
+ Support -&gt; USB Gadget Support -&gt; EHCI Debug Device Gadget=m</li>
+ <li>Build the module:</li>
+ </ul>
+<pre>
+$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- -j4 (is it possoble to build only the gadget modules)
+$ mkdir ../tmp &amp;&amp; make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- INSTALL_MOD_PATH=../tmp modules_install
+</pre>
+ <ul>
+ <li>on BBB, backup /lib/modules/3.8.13-bone70/kernel/drivers/usb/gadget
+ (i.e. mv
+ /lib/modules/3.8.13-bone70/kernel/drivers/usb/gadget $HOME)
+ </li>
+ <li>copy the freshly compiled usb/gadget dir to /lib/modules/3.8.13-bone70/kernel/drivers/usb</li>
+ <li>restart BBB</li>
+ <li>Remove all g_* modules (rmmod
+ g_&lt;&gt;)
+ </li>
+ <li>modprobpe g_dbgp</li>
+ </ul>
+ <h3 id="ConfigurelibrebootwithEHCIdebug">Configure libreboot with
+ EHCI debug</h3>
+ <p>
+ Libreboot(coreboot) should be configured with debug turned on and to
+ push debug messages to the EHCI debug port.<br />If you&#8217;ve
+ downloaded the binary distribution, you can check if it is properly
+ configured in the following way:
+ </p>
+ <ul>
+ <li>Go to the libreboot dist root directory cd
+ $libreboot_bin</li>
+ <li>Locate the rom image for your target (I will call it: $img_path)
+ </li>
+ <li>Running the following command will extract the config in a
+ file ./my_config:
+ </li>
+ </ul>
+<pre>
+./cbfstool/i686/cbfstool $img_path extract -n config -f ./my_config
+</pre>
+ <ul>
+ <li>Make sure that the following params in the config are set as
+ following:</li>
+ </ul>
+<pre>
+CONFIG_USBDEBUG=y (Generic Drivers -&gt; USB 2.0 EHCI debug dongle support)
+CONFIG_USBDEBUG_IN_ROMSTAGE=y (Generic Drivers -&gt; Enable early (pre-RAM) usbdebug)
+CONFIG_USBDEBUG_HCD_INDEX=&lt;HCD Index of usb controller - see below&gt; (Generic Drivers -&gt; Index for EHCI controller to use with usbdebug)
+CONFIG_USBDEBUG_DEFAULT_PORT=&lt;USB Debug port - see below&gt; (Generic Drivers -&gt; Default USB port to use as Debug Port)
+</pre>
+ <p>
+ The following three are behind radio button in the menu. Only the first
+ one<sup class="footnote"><a href="#___fn2">2</a></sup> should be = y
+ </p>
+<pre>
+USBDEBUG_DONGLE_STD=y (Generic Drivers -&gt; Type of dongle (Net20DC or compatible) -&gt; Net20DC or compatible)
+CONFIG_USBDEBUG_DONGLE_BEAGLEBONE=n (Generic Drivers -&gt; Type of dongle (Net20DC or compatible) -&gt; BeagleBone)
+CONFIG_USBDEBUG_DONGLE_BEAGLEBONE_BLACK=n (Generic Drivers -&gt; Type of dongle (Net20DC or compatible) -&gt; BeagleBone Black)
+</pre>
+ <p id="___fn2" class="footnote">
+ <sup>2</sup> The g_dbgp module on BeagleBone Black (Rev. C) reports it self as Net20DC, the
+ other options are for older BB(B) - ver1. This is documented <a
+ href="https://johnlewis.ie/coreboot-ehci-debug-gadget-demonstration/">here</a>
+ (also tested/verified).
+ </p>
+ <p>
+ Then:<br />
+<pre>
+CONFIG_CONSOLE_USB=y (Console -&gt; USB dongle console output)
+</pre>
+ </p>
+ <p>
+ Also
+ Debugging ---&gt; Output verbose XYZ
+ ) (<b>FIXME</b> somebody verify these):
+ </p>
+<pre>
+CONFIG_DEBUG_CBFS=y (Output verbose CBFS debug messages )
+CONFIG_HAVE_DEBUG_RAM_SETUP=y (??? What/where is this)
+CONFIG_DEBUG_RAM_SETUP=y (Output verbose RAM init debug messages)
+CONFIG_DEBUG_SMI=y (Output verbose SMI debug messages)
+CONFIG_DEBUG_ACPI=y (Output verbose ACPI debug messages )
+CONFIG_DEBUG_USBDEBUG=y (Output verbose USB 2.0 EHCI debug dongle messages)
+</pre>
+ <p>If some of the above mentioned configuration options are not as
+ specified, you have to configure and compile libreboot yourself. Please
+ refer to the doc(<b>FIXME: link</b> about compiling libreboot.</p>
+ <h4 id="SelectingHCDIndexandUSBDebugport">
+ Selecting
+ HCD Index
+ and
+ USB Debug port
+ </h4>
+ <p>
+ This applies (and works) only if the USB controller that supports debug
+ (found in the first section) is from Intel.<br />If the PCI ID of the
+ port you found in the first section is
+ 0000:00:1a.0
+ or
+ 0000:00:1d.0
+ , you are ok. Otherwise you have to try without guarantee that will
+ work.
+ </p>
+ <p>
+ If the externally exposed port is on a bus with
+ PCI ID == 0000:00:1a.0
+ then for
+ CONFIG_USBDEBUG_HCD_INDEX
+ choose 2, otherwise choose 0
+ .
+ </p>
+ <p>
+ For
+ CONFIG_USBDEBUG_DEFAULT_PORT
+ choose the port from the first section that correspond to the
+ PCI ID
+ </p>
+ <p>
+ Notes:<br />The above is based on the implementation of
+ coreboot/src/southbridge/intel/common/usb_debug.c : pci_ehci_dbg_dev()
+ .<br />This is enough as it applies for the supported GM45/G45
+ Thinkpads. coreboot support some other contollers too, but they are
+ irellevent for libreboot (for now).
+ </p>
+ <ul>
+ <li>On T500 (with switchable GPU) the debug ports for both intel
+ controllers is exposed.</li>
+ <li>On x200t the debug ports for both intel controllers is
+ exposed.</li>
+ </ul>
+ <h3 id="Howtogetthedebuglogs">How to get the debug logs</h3>
+ <ul>
+ <li>Plug the USB cable in the target&#8217;s debug port (the one
+ you found in step 1) and BBB&#8217;s mini-B USB</li>
+ <li>Make sure no other then g_dbgp of the g_*
+ modules is loaded on your BBB
+ </li>
+ <li>On the BBB:</li>
+ </ul>
+<pre>
+stty -icrnl -inlcr -F /dev/ttyGS0
+cat /dev/ttyGS0
+</pre>
+ <ul>
+ <li>Power on the target with libreboot</li>
+ <li>You should see debug logs comming on your BBB console</li>
+ </ul>
+ <p>
+ Note that this is not permanent on BBB, if you reboot it, you have to
+ rmmod g_*
+ and
+ modprobe g_dbgp
+ </p>
+ <h3 id="EnebleEHCIDebugonthetargetskerneloptionalrecommended">Eneble
+ EHCI Debug on the target&#8217;s kernel (optional, recommended)</h3>
+ <p>You have to know how to compile kernel for your target.</p>
+ <ol>
+ <li>Check if early debugging is already enabled: grep
+ CONFIG_EARLY_PRINTK_DBGP /boot/config-&lt;ver&gt;</li>
+ <li>If enabled, you do not have to compile the kernel (skip this
+ step). Otherwise, prepare kernel source for your distribution and
+ select (Kernel hacking -&gt; Early printk via EHCI debug
+ port). Compile and install the new kernel.
+ </li>
+ <li>Edit your grub configuration and add following to the kenel
+ parameters<sup class="footnote"><a href="#___fn20">20</a></sup><sup
+ class="footnote"><a href="#___fn21">21</a></sup>: earlyprintk=dbgp,keep.
+ Also, try: earlyprintk=dbgp&lt;N&gt;,keep where N
+ is the debug port id if the first does not work.
+ </li>
+ </ol>
+ <h3 id="References">References</h3>
+ <p id="___fn10" class="footnote">
+ <sup>10</sup> <a href="http://www.coreboot.org/EHCI_Debug_Port">EHCI
+ Debug Port</a>
+ </p>
+ <p id="___fn11" class="footnote">
+ <sup>11</sup> <a
+ href="https://johnlewis.ie/coreboot-ehci-debug-gadget-demonstration/">coreboot
+ EHCI debug gadget demonstration</a>
+ </p>
+ <p id="___fn12" class="footnote">
+ <sup>12</sup> <a href="http://www.coreboot.org/EHCI_Gadget_Debug">EHCI
+ Gadget Debug</a>
+ </p>
+ <p id="___fn13" class="footnote">
+ <sup>13</sup> <a
+ href="http://www.coreboot.org/images/8/88/Ehci-debug-gadget-patches.tar.gz">Ehci-debug-gadget-patches.tar.gz</a>
+ </p>
+ <p id="___fn14" class="footnote">
+ <sup>14</sup> <a
+ href="http://wiki.beyondlogic.org/index.php/BeagleBoneBlack_Building_Kernel">Compiling
+ the BeagleBone Black Kernel</a>
+ </p>
+ <p id="___fn15" class="footnote">
+ <sup>15</sup>
+ http://dumb-looks-free.blogspot.ca/2014/06/beaglebone-black-bbb-compile-kernel.html
+ </p>
+ <p id="___fn16" class="footnote">
+ <sup>16</sup>
+ http://dumb-looks-free.blogspot.fr/2014/06/beaglebone-black-bbb-kernal-headers.html
+ </p>
+ <p id="___fn17" class="footnote">
+ <sup>17</sup> <a href="http://elinux.org/Building_BBB_Kernel">Building
+ BBB Kernel</a>
+ </p>
+ <p id="___fn18" class="footnote">
+ <sup>18</sup>
+ http://komposter.com.ua/documents/USB-2.0-Debug-Port%28John-Keys%29.pdf
+ </p>
+ <p id="___fn19" class="footnote">
+ <sup>19</sup> <a href="http://cs.usfca.edu/~cruse/cs698s10/">Exploring
+ USB at the Hardware/Software Interface</a>
+ </p>
+ <p id="___fn20" class="footnote">
+ <sup>20</sup>
+ https://www.kernel.org/doc/Documentation/x86/earlyprintk.txt
+ </p>
+ <p id="___fn21" class="footnote">
+ <sup>21</sup> https://wiki.ubuntu.com/Kernel/Debugging/USBearlyprintk
+ </p>
+ <p>
+ <b>TODO</b>:
+ </p>
+ <ol>
+ <li>grub does not send messages to EHCI debug. Investigate.</li>
+ <li>The section &#8220;Configure libreboot with EHCI debug&#8221;
+ can be skipped/simplified if a common configuration works for all
+ relevant targets is selected as defualt</li>
+ <li>Patch and compule g_dbgp on BBB instead cross-compile</li>
+ <li>Find a simple way to send debug messages from targets userland</li>
+ </ol>
</div>
<div class="section">
@@ -434,6 +825,7 @@ from #coreboot
<p>
Copyright &copy; 2014, 2015 Francis Rowe &lt;info@gluglug.org.uk&gt;<br/>
Copyright &copy; 2015 Patrick &quot;P. J.&quot; McDermott &lt;pj@pehjota.net&gt;<br/>
+ Copyright &copy; 2015 Pi Van Den Cirkel <opdecirkel@gmail.com>
This document is released under the Creative Commons Attribution-ShareAlike 4.0 International Public License and all future versions.
A copy of the license can be found at <a href="../license.txt">../license.txt</a>.
</p>