From 15a27b612b1da36173017dd671763ce455f319ad Mon Sep 17 00:00:00 2001 From: Timothy Pearson Date: Sun, 21 Jun 2015 16:27:03 -0500 Subject: [PATCH 065/139] src/southbridge/amd/sb700: Reset SATA controller in AHCI mode during startup In AHCI mode SeaBIOS randomly fails to detect disks (AHCI timeouts), with the probability of a failure increasing with the number of disks connected to the controller. Resetting the SATA controller appears to show the true state of the underlying hardware, allowing the drive detection code to attempt link renegotiation as needed. Change-Id: Ib1f7c5f830a0cdba41cb6f5b05d759adee5ce369 Signed-off-by: Timothy Pearson --- src/southbridge/amd/sb700/sata.c | 47 ++++++++++++++++++++++++++++++---------- 1 file changed, 35 insertions(+), 12 deletions(-) diff --git a/src/southbridge/amd/sb700/sata.c b/src/southbridge/amd/sb700/sata.c index 24f78dd..d51baa1 100644 --- a/src/southbridge/amd/sb700/sata.c +++ b/src/southbridge/amd/sb700/sata.c @@ -135,6 +135,8 @@ static void sata_init(struct device *dev) /* get rev_id */ rev_id = pci_read_config8(sm_dev, 0x08) - 0x28; + printk(BIOS_SPEW, "rev_id=%x\n", rev_id); + if (sata_ahci_mode) { /* Enable link latency enhancement on A14 and above */ if (rev_id >= 0x14) { @@ -245,6 +247,27 @@ static void sata_init(struct device *dev) write32(sata_bar5 + 0xfc, dword); } + if (sata_ahci_mode) { + /* FIXME + * SeaBIOS does not know how to spin + * up the drives and therefore hangs + * in AHCI init if this is enabled... + */ + /* Enable staggered spin-up */ + dword = read32(sata_bar5 + 0x00); +#if 0 + dword |= 0x1 << 27; +#else + dword &= ~(0x1 << 27); +#endif + write32(sata_bar5 + 0x00, dword); + + /* Reset the HBA to avoid stuck drives in SeaBIOS */ + dword = read32(sata_bar5 + 0x04); + dword |= 0x1; + write32(sata_bar5 + 0x04, dword); + } + /* Write protect Sub-Class Code */ byte = pci_read_config8(dev, 0x40); byte &= ~(1 << 0); @@ -371,21 +394,21 @@ static void sata_init(struct device *dev) } /* Below is CIM InitSataLateFar */ - /* Enable interrupts from the HBA */ - byte = read8(sata_bar5 + 0x4); - byte |= 1 << 1; - write8((sata_bar5 + 0x4), byte); - if (!sata_ahci_mode) { - /* Clear error status */ - write32((sata_bar5 + 0x130), 0xFFFFFFFF); - write32((sata_bar5 + 0x1b0), 0xFFFFFFFF); - write32((sata_bar5 + 0x230), 0xFFFFFFFF); - write32((sata_bar5 + 0x2b0), 0xFFFFFFFF); - write32((sata_bar5 + 0x330), 0xFFFFFFFF); - write32((sata_bar5 + 0x3b0), 0xFFFFFFFF); + /* Enable interrupts from the HBA */ + byte = read8(sata_bar5 + 0x4); + byte |= 1 << 1; + write8((sata_bar5 + 0x4), byte); } + /* Clear error status */ + write32((sata_bar5 + 0x130), 0xFFFFFFFF); + write32((sata_bar5 + 0x1b0), 0xFFFFFFFF); + write32((sata_bar5 + 0x230), 0xFFFFFFFF); + write32((sata_bar5 + 0x2b0), 0xFFFFFFFF); + write32((sata_bar5 + 0x330), 0xFFFFFFFF); + write32((sata_bar5 + 0x3b0), 0xFFFFFFFF); + /* Clear SATA status,Firstly we get the AcpiGpe0BlkAddr */ /* ????? why CIM does not set the AcpiGpe0BlkAddr , but use it??? */ -- 1.9.1