summaryrefslogtreecommitdiffstats
path: root/docs/install
diff options
context:
space:
mode:
Diffstat (limited to 'docs/install')
-rw-r--r--docs/install/bbb_setup.html24
1 files changed, 19 insertions, 5 deletions
diff --git a/docs/install/bbb_setup.html b/docs/install/bbb_setup.html
index 4da7623..74d8f19 100644
--- a/docs/install/bbb_setup.html
+++ b/docs/install/bbb_setup.html
@@ -36,11 +36,12 @@
External SPI programmer: <b>BeagleBone Black</b> (rev. C)
is highly recommended. Sometimes referred to as 'BBB'.
<a href="http://beagleboard.org/black">This page</a> contains a list of distributors.
+ farnell sells them - <a href="http://farnell.com/">http://farnell.com/</a>
</li>
<li>
- Electrical tape: cover the entire bottom surface of the BBB (the part that
+ Electrical/insulative tape: cover the entire bottom surface of the BBB (the part that
rests on a surface). This is important, when placing the BBB on top of a board
- so that nothing shorts.
+ so that nothing shorts. - easy to find in most hardware/electronics stores
</li>
<li>
Clip for connecting to the flash chip: if you have a SOIC-16
@@ -49,15 +50,24 @@
need the <b>Pomona 5250</b> or equivalent. Do check which chip you have,
before ordering a clip. Also, make sure to buy at least two clips
(they break easily).
+ - Farnell sells these, and ships to many countries. <a href="http://farnell.com/">http://farnell.com/</a>
+ - Some people find these difficult to get, especially in South America. If you have more links to suppliers,
+ please contact the libreboot project with the relevant information.
</li>
<li>
<b>External 3.3V DC power supply</b>, for powering the flash chip.
An ATX power supply / PSU (common on Intel/AMD desktop computers) will work for this.
+ A lab PSU (DC) will also work (adjusted to 3.3V). Etc.
+ <ul>
+ <li>Getting a multimeter might be worthwhile, to verify that it's supplying 3.3V</li>
+ </ul>
</li>
<li>
<b>External 5V DC power supply</b> (barrel connector), for powering the BBB.
The BeagleBone can have power supplied via USB, but a
- dedicated power supply is recommended.
+ dedicated power supply is recommended. These should be easy to find in most places
+ that sell electronics. - <b>OPTIONAL. Only needed if not powering with the USB cable, or if you want
+ to use <a href="bbb_ehci.html">EHCI debug</a></b>
</li>
<li>
<b>Pin header / jumper cables</b> (2.54mm / 0.1&quot; headers)
@@ -69,16 +79,20 @@
<li>dupont (this is just one possible brand name)</li>
<li>Often used on breadboards, so they might be called breadboard cables</li>
<li>Maybe they are called <b>wires</b> instead of cables or leads</li>
+ <li>They are also the same cables used on the GPIOs on the RPi</li>
+ <li><b>adafruit.com</b> sells them, and there are others</li>
+ <li><b>Some people find these difficult to buy. Contact the libreboot project if you have more links to sellers.</b></li>
+ <li>You might also be able to make these cables yourself.</li>
</ul>
</li>
<li>
<b>Mini USB A-B cable</b> (the BeagleBone probably already comes
- with one.)
+ with one.) - <b>OPTIONAL - only needed for <a href="bbb_ehci.html">EHCI debug</a> or for serial/ssh access without ethernet cable (g_multi kernel module)</b>
</li>
<li>
<b>FTDI TTL cable or debug board</b>, for accessing the serial console on your BBB.
<a href="http://elinux.org/Beagleboard:BeagleBone_Black_Serial">This page</a> contains
- a list.
+ a list. - <b>OPTIONAL - only needed for serial console on the BBB, if not using SSH via ethernet cable</b>
</li>
</ul>