grub.cfg: don't search for grub.cfg on RAID volumes

Unfortunately, this means that GRUB is searching all devices,
which again causes boot delays on buggy DVD/CD drives in ahci1
or ata0

1 files changed, 5 insertions, 12 deletions

diff --git a/resources/grub/config/menuentries/common.cfg b/resources/grub/config/menuentries/common.cfg
index 9e5c04e..95599df 100644
--- a/resources/grub/config/menuentries/common.cfg
+++ b/resources/grub/config/menuentries/common.cfg
@@ -24,25 +24,20 @@ menuentry 'Load Operating System (incl. fully encrypted disks)  [o]' --hotkey='o
 # GRUB handles (almost) every possible disk setup, but only the location of /boot is actually important,
 # since GRUB only loads the user's config. As soon as the kernel takes over, libreboot's done.
 
-# RAID, filesystems and encryption on both raw devices and partitions in all various combinations
+# filesystems and encryption on both raw devices and partitions in all various combinations
 # need to be supported. Since full disk encryption is possible with GRUB as payload and probably desired/used
 # by most users, libreboot GRUB config tries to load the operating system (kernel) in the following way:
 
-	# 1. Try to decrypt raw devices first. This <your disk setup> inside a LUKS container is pretty common
-	#	a) Try RAID first, they might be used (accross multiple (raw) devices)
-	#	b) Try MBR/GPT partitions at last, one might still conviniently uses a single partition
+	# Try to decrypt raw devices first. This <your disk setup> inside a LUKS container is pretty common
 
 	# prompt user for passphrase if LUKS header is found
-	for d in md/0 ahci0; do 		cryptomount ${d}; done
-	for j in 1 2 3 4 5 6 7 8 9; do cryptomount "ahci0,${j}"; done
-
-	#   (This way, we only need to scan for encrypted data once while covering every possible disk setup,
-	#    be it BTRFS/ZFS/ext4/etc. (on LUKS) (on RAID) on/across raw devices/MBR/GPT
+	cryptomount ahci0
+	for j in 1 2 3 4 5 6 7 8 9; do 	cryptomount ahci0,${j}; done
 
 	# 2. Look for user config. If the above routine successfully decrypted a LUKS container, its content
 	#    will be searched before everything else for obvious reasons. Regardless of this, the devices'
 	#    hirachy stays the same.
-	for d in crypto0 md/0 ahci0; do 	switch_to_grub_config ${d}; done
+	for d in crypto0 ahci0; do 	switch_to_grub_config ${d}; done
 	for j in 1 2 3 4 5 6 7 8 9; do
 		for d in crypto0 ahci0; do 	switch_to_grub_config "${d},${j}"; done
 	done
@@ -52,8 +47,6 @@ menuentry 'Load Operating System (incl. fully encrypted disks)  [o]' --hotkey='o
 	if [ $? = 0 ]; then
 		kf="-k (${kf})/keyfile ${d}"
 	fi
-	#   (This way, we only need to scan for encrypted data once while covering every possible disk setup,
-	#    be it BTRFS/ZFS/ext4/etc. (on LUKS) (on RAID) on/across raw devices/MBR/GPT
 	for d in ${devs}; do
 		cryptomount ${kf} ${d}
 	done