docs/install/x200_external.html: Show images, don't link.

1 files changed, 7 insertions, 10 deletions

diff --git a/docs/install/x200_external.html b/docs/install/x200_external.html
index 8c1df7e..b3de46b 100644
--- a/docs/install/x200_external.html
+++ b/docs/install/x200_external.html
@@ -94,24 +94,22 @@ POMONA 5250 (correlate with the BBB guide)
  3.3V PSU RED    -       - 17 - this is pin 1 on the flash chip. in front of it is the screen.
 ===  right side of the X200 (where the audio jacks are) ===
 <i>This is how you will connect. Numbers refer to pin numbers on the BBB, on the plugs near the DC jack.</i>
-Here is a photo of the SOIC-8 flash chip: <a href="images/x200/soic8.jpg" alt="freenode IRC #libreboot 01:42 UK/London timezone February 8th 2015: pehjota: fchmmr: Here are two photos in the camera's configured resolution; resize them as you wish: http://www.pehjota.net/~pj/x200/soic-8/.  License: CC BY-SA 3.0 or later.  If you want other angles or anything, let me know.">images/x200/soic8.jpg</a>
-(image copyright 2015 Patrick &quot;P. J.&quot; McDermott &lt;pj@pehjota.net&gt;, CC BY-SA 3.0 or later)
+Here is a photo of the SOIC-8 flash chip:<br/>
+<img title="Copyright 2015 Patrick &quot;P. J.&quot; McDermott &lt;pj@pehjota.net&gt;, CC BY-SA 3.0 or later" src="images/x200/soic8.jpg" alt="freenode IRC #libreboot 01:42 UK/London timezone February 8th 2015: pehjota: fchmmr: Here are two photos in the camera's configured resolution; resize them as you wish: http://www.pehjota.net/~pj/x200/soic-8/.  License: CC BY-SA 3.0 or later.  If you want other angles or anything, let me know." alt="" />
 
 Look at the pads in that photo, on the left and right. Those are for SOIC-16. Would it be possible to remove the SOIC-8 and solder a SOIC-16
 chip on those pins?
 </pre>
 			<p>
 				<b>On the X200S the flash chip is underneath the board, in a WSON package. 
-				The pinout is very much the same as a SOIC-8, except you need to solder (there are no clips available). 
-				<a href="images/x200/wson_soldered.jpg">images/x200/wson_soldered.jpg</a> (image copyright (C) 2014 <a href="mailto:sgsit@libreboot.org">Steve Shenton</a> under CC-BY-SA 4.0
-				or higher, same license that this document uses) shows it wired (soldered) and
-				connected to a BBB.</b>
+				The pinout is very much the same as a SOIC-8, except you need to solder (there are no clips available).<br/>
+				The following image shows how this is done:</b><br/>
+				<img src="images/x200/wson_soldered.jpg" title="Copyright 2014 Steve Shenton &lt;sgsit@libreboot.org&gt; under CC-BY-SA 4.0" alt="" />
 				<br/>
 				In this image, a pin header was soldered onto the WSON. Another solution might be to de-solder the WSON-8 chip and put a SOIC-8 there instead.
 				Check the list of SOIC-8 flash chips at <a href="../hcl/gm45_remove_me.html#flashchips">../hcl/gm45_remove_me.html#flashchips</a> but
 				do note that these are only 4MiB (32Mb) chips. The only X200 SPI chips with 8MiB capacity are SOIC-16. For 8MiB capacity in this case,
 				the X201 SOIC-8 flash chip (Macronix 25L6445E) might work.
-				<br/>
 				Another possible solution: ground GPIO33 and boot up in non-descriptor mode. This might make software flashing possible, if
 				it's possible to circumvent any flashing protections that might exist.
 			</p>
@@ -120,9 +118,8 @@ chip on those pins?
 				Connect Pomona 5252/5250 to the X200 flash chip, and dump/flash
 			</h2>
 				<p>
-					<a href="images/x200/x200_pomona.jpg">images/x200/x200_pomona.jpg</a>
-					shows everything connected. In this picture, the X200 is being flashed
-					with the BBB.
+					The following photo shows an X200 flashed using the BBB:<br/>
+					<img src="images/x200/x200_pomona.jpg" alt="" />
 				</p>
 				<p>
 					Remove the battery from your X200, then remove all the screws on