blob: 0b390fbcace29dcf032db926e1b3b2f0b46c53d1 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
|
# generated by Slic3r 1.2.9 on Tue Aug 15 15:26:07 2017
bed_shape = -2x-2,156x-2,156x156,-2x156
before_layer_gcode =
end_gcode = ; Begin LulzBot Mini end sequence\nM400 ; wait for current moves to finish (clear buffer)\nM104 S0 ; Hotend off\nM140 S0 ; heated bed heater off (if you have it)\nM107 ; fans off\nG92 E5 ; set extruder to 5mm for retract on print end\nG1 X5 Y5 Z156 E0 F10000 ; move to cooling positioning\nM190 R50 ; wait for bed to cool\nM140 S0 ; turn off bed temp\nG1 X145 Y175 Z156 F1000 ; move to cooling positioning\nM84 ; steppers off\nG90 ; absolute positioning\n; End LulzBot Mini end sequence\n
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
nozzle_diameter = 0.5
octoprint_apikey =
octoprint_host =
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1
retract_length_toolchange = 10
retract_lift = 0.2
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
start_gcode = ; Begin LulzBot Mini start sequence\n; File name: [input_filename]\n; Print time: [timestamp]\n; Printer preset: [printer_preset]\n; Filament preset: [filament_preset]\n; Print preset: [print_preset]\n; First layer height: [first_layer_height]\n; Layer height: [layer_height]\n; Fill: [fill_density] [fill_pattern] at [fill_angle] degrees\n; Filament Diameter: [filament_diameter]\n; Nozzle Diameter: [nozzle_diameter]\nG21 ; metric values\nG90 ; absolute positioning\nM82 ; set extruder to absolute mode\nM107 ; start with the fan off\nG92 E0 ; set extruder position to 0\nM140 S[first_layer_bed_temperature] ; get bed heating up\nG28 ; home all\nM109 S140 ; set to cleaning temp and wait\nG1 Z150 E-30 F75 ; suck up XXmm of filament\nM109 S140 ; heat up rest of way\nG1 X45 Y174 F11520 ; move behind scraper\nG1 Z0 F1200 ; CRITICAL: set Z to height of top of scraper\nG1 X45 Y174 Z-.5 F4000 ; wiping ; plunge into wipe pad\nG1 X55 Y172 Z-.5 F4000 ; wiping\nG1 X45 Y174 Z0 F4000 ; wiping\nG1 X55 Y172 F4000 ; wiping\nG1 X45 Y174 F4000 ; wiping\nG1 X55 Y172 F4000 ; wiping\nG1 X45 Y174 F4000 ; wiping\nG1 X55 Y172 F4000 ; wiping\nG1 X60 Y174 F4000 ; wiping\nG1 X80 Y172 F4000 ; wiping\nG1 X60 Y174 F4000 ; wiping\nG1 X80 Y172 F4000 ; wiping\nG1 X60 Y174 F4000 ; wiping\nG1 X90 Y172 F4000 ; wiping\nG1 X80 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X80 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X80 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X110 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X110 Y174 F4000 ; wiping\nG1 X100 Y172 F4000 ; wiping\nG1 X110 Y174 F4000 ; wiping\nG1 X115 Y172 Z-0.5 F1000 ; wipe slower and bury noz in cleanish area\nG1 Z10 ; raise z\nG28 X0 Y0 ; home x and y\nM109 S140 ; set to probing temp\nM204 S300 ; set accel for probing\nG29 ; Probe\nM204 S2000 ; set accel back to normal\nG1 X5 Y15 Z10 F5000 ; get out the way\nG4 S1 ; pause\nM400 ; clear buffer\nM109 S[first_layer_temperature] ; set extruder temp and wait\nG4 S15 ; wait for bed to temp up\nG1 Z2 E0 F75 ; extrude filament back into nozzle\nM140 S[first_layer_bed_temperature] ; get bed temping up during first layer\n; End LulzBot Mini start sequence\n
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
z_offset = 0.1
|
