dotfiles/slic3r.git - Slic3r configuration

	Commit message (Collapse)	Author	Age	Files	Lines
...
*	Base: Reduce solid infill threshold area	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Increase minimum skirt length	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Reduce infill/perimeters overlap	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Run 4 threads	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Combine infill and only infill where needed	P. J. McDermott	2019-02-14	1	-3/+3
\|
*	Base: Increase speeds	P. J. McDermott	2019-02-14	1	-8/+8
\|
*	TAZ 6, SE v2.1 G-code: Move to wiping pad 0.6 s faster	P. J. McDermott	2019-02-14	3	-4/+4
\|
*	TAZ 6, SE v2.1, eSUN PLA: Wipe while retracting	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	TAZ 6, SE v2.1, eSUN PLA; Base: Lift on retract, increase travel speed	P. J. McDermott	2019-02-14	2	-4/+4
\|
*	TAZ 6, SE v2.1, eSUN PLA: Increase retraction length and speed	P. J. McDermott	2019-02-14	1	-3/+3
\|
*	eSUN PLA, 3 mm: Decrease temperature	P. J. McDermott	2019-02-13	1	-3/+3
\|
*	Base: Increase travel speed	P. J. McDermott	2019-02-13	1	-2/+2
\|
*	Base: New print preset, based on SFF-8201 HA	P. J. McDermott	2019-02-13	1	-0/+86
\|
*	TAZ 6, SE v2.1, eSUN PLA: Decrease retraction and lift	P. J. McDermott	2019-02-13	1	-3/+3
\|
*	TAZ 6, SE v2.1, eSUN PLA: Increase retraction	P. J. McDermott	2019-02-13	1	-3/+3
\|
*	printer: Wiping what?	P. J. McDermott	2019-02-12	3	-3/+3
\|
*	printer: Prime nozzle in a corner, not center	P. J. McDermott	2019-02-12	3	-5/+5
\| \| \| \| \|	Priming drops filament onto the bed, which should be done outside of the print as much as possible.
*	slic3r.ini: Switch to PLA	P. J. McDermott	2019-02-12	1	-2/+2
\|
*	printer: Add TAZ 6 SE v2.1 eSUN HIPS config	P. J. McDermott	2019-02-12	1	-0/+27
\|
*	printer: Preprocess G-code and inject into config	P. J. McDermott	2019-02-12	1	-2/+2
\| \| \| \|	Automatically done by slic3r-gpp.
*	printer: Add "eSUN" in TAZ 6 printer/filament name	P. J. McDermott	2019-02-12	2	-1/+1
\|
*	filament: Add eSUN HIPS rc file	P. J. McDermott	2019-02-12	1	-0/+4
\|
*	filament: Add eSUN PLA rc file	P. J. McDermott	2019-02-12	1	-0/+4
\|
*	printer: Remind Marlin of bed temp in TAZ 6 start G-code	P. J. McDermott	2019-02-12	1	-1/+1
\|
*	printer: Parameterize temperatures in TAZ 6 G-code files	P. J. McDermott	2019-02-12	2	-24/+24
\|
*	printer: Remove filament from TAZ 6 G-code file names	P. J. McDermott	2019-02-12	2	-0/+0
\|
*	filament: Rename "PLA, 3 mm" to "eSUN PLA, 3 mm"	P. J. McDermott	2019-02-11	1	-0/+0
\|
*	printer: Edit TAZ 6 end G-code	P. J. McDermott	2019-02-11	1	-2/+2
\| \| \| \|	Beep and stop the timer after the bed moves forward for print removal.
*	printer: Add TAZ 6 end G-code	P. J. McDermott	2019-02-11	1	-0/+44
\| \| \| \|	With an option to keep the hotend and bed warm for the next print!
*	printer: Edit TAZ 6 start G-code	P. J. McDermott	2019-02-11	1	-3/+3
\| \| \| \| \| \|	* Allow heating to wiping temperature before retraction completes * Allow heating to first layer temperature before probing completes * Improve centering M400 comment
*	printer: Edit TAZ 6 start G-code	P. J. McDermott	2019-02-11	1	-6/+6
\| \| \| \| \| \| \| \| \|	* Make M400 comments more specific * Allow first-layer heating to occur immediately after probing, instead of waiting to lift above washer * Drop G4 (dwell) command * Add M400 command to wait until end of extruder priming before showing "Printing..."
*	printer: Edit TAZ 6 start G-code	P. J. McDermott	2019-02-11	1	-11/+10
\| \| \| \| \| \| \| \|	* Drop useless M117 commands * Remind Marlin of target temperatures in M109 commands * Add pauses (M400) after movement commands (G1 and G28) and before M117, M104, etc. * Align wiping command comments
*	printer: Add untested TAZ 6 start G-code	P. J. McDermott	2019-02-10	1	-0/+129
\|
*	printer: Begin LulzBot TAZ 6, Single Extruder v2.1	P. J. McDermott	2019-02-10	2	-4/+31
\| \| \| \|	Also add logi1's window geometry in .Slic3r/slic3r.ini.
*	printer: Make end G-code result in extruder at 0 mm	P. J. McDermott	2017-08-22	3	-5/+5
\|
*	filament: Reduce first layer bed temperature	P. J. McDermott	2017-08-21	2	-3/+3
\|
*	printer: Move X axis after probing	P. J. McDermott	2017-08-21	3	-3/+4
\| \| \| \| \| \| \|	Otherwise, the firmware detects that an endstop is triggered and blocks any other moves: echo:endstops hit: X:0.00
*	print: Move toolhead farther up for cooling and removal	P. J. McDermott	2017-08-21	3	-5/+5
\| \| \| \|	This should give a taller usable print area.
*	printer: Move bed farther forward for print removal	P. J. McDermott	2017-08-21	3	-4/+4
\|
*	print: Slow down perimeter print speeds	P. J. McDermott	2017-08-21	2	-6/+6
\| \| \| \| \| \| \| \| \| \|	Loading two SFF-8201 HAs into Printrun, before: Estimated duration: 11 layers, 0:18:04 Loading two SFF-8201 HAs into Printrun, after: Estimated duration: 11 layers, 0:19:49
*	print: Generate verbose (commented) G-code	P. J. McDermott	2017-08-21	2	-3/+3
\|
*	slic3r.ini: Update main frame position, presets, etc.	P. J. McDermott	2017-08-21	1	-7/+7
\|
*	print: Add infill and double print speeds	P. J. McDermott	2017-08-21	1	-10/+10
\| \| \| \|	Also increase skirt distance.
*	print: Reduce skirt distance print-v2	P. J. McDermott	2017-08-21	1	-2/+2
\| \| \| \| \|	This is done to fit two SFF-8201 HAs with a 4-mm skirt on a LulzBot Mini bed.
*	print: Increase all print speeds to 40 mm/s	P. J. McDermott	2017-08-21	1	-7/+7
\|
*	print: Reduce perimeters and top/bottom solid layers to 2	P. J. McDermott	2017-08-21	1	-4/+4
\|
*	print: Add new preset	P. J. McDermott	2017-08-21	2	-18/+86
\| \| \| \| \|	Use git-log or git-show with `-M13%` to see the changes between the presets.
*	filament: Enable fan starting on second layer	P. J. McDermott	2017-08-20	1	-2/+2
\|
*	filament: Raise HIPS temperatures	P. J. McDermott	2017-08-20	1	-5/+5
\|
*	filament: Lower HIPS temperatures	P. J. McDermott	2017-08-20	1	-5/+5
\|