| Commit message (Collapse) | Author | Age | Files | Lines | |
|---|---|---|---|---|---|
| ... | |||||
| * | print: Add new preset | P. J. McDermott | 2017-08-21 | 2 | -18/+86 |
| | | | | | | Use git-log or git-show with `-M13%` to see the changes between the presets. | ||||
| * | filament: Enable fan starting on second layer | P. J. McDermott | 2017-08-20 | 1 | -2/+2 |
| | | |||||
| * | filament: Raise HIPS temperatures | P. J. McDermott | 2017-08-20 | 1 | -5/+5 |
| | | |||||
| * | filament: Lower HIPS temperatures | P. J. McDermott | 2017-08-20 | 1 | -5/+5 |
| | | |||||
| * | filament: Add eSUN HIPS preset | P. J. McDermott | 2017-08-20 | 1 | -0/+17 |
| | | |||||
| * | printer: Add custom start/end G-code files | P. J. McDermott | 2017-08-20 | 2 | -0/+126 |
| | | | | | | | | | | | | G-code is easier to read in separate files than in Slic3r configuration. This G-code is based on the LulzBot Mini G-code provided by Aleph Objects. To increase speed, I added commands to set the hotend temperature without waiting and arranged some commands like G28 and G1 to run while the hotend heats up. For better clarity, I also added more comments and blank lines and vertically aligned wiping command arguments. | ||||
| * | printer: Rewrite G-code, change bed size, rename preset | P. J. McDermott | 2017-08-20 | 2 | -27/+27 |
| | | |||||
| * | printer: Use HIPS retraction, wiping, and probing temps | P. J. McDermott | 2017-08-20 | 1 | -2/+2 |
| | | |||||
| * | printer: Reduce bed size and restore Z offset to 0 | P. J. McDermott | 2017-08-20 | 1 | -3/+3 |
| | | |||||
| * | printer: Increase retraction speed and Z offset | P. J. McDermott | 2017-08-20 | 1 | -3/+3 |
| | | |||||
| * | Reduce PLA extrusion temperature to 200 | P. J. McDermott | 2016-04-10 | 2 | -4/+4 |
| | | |||||
| * | Reduce printer Z offset | P. J. McDermott | 2016-04-10 | 2 | -3/+3 |
| | | |||||
| * | Set PLA diameter | P. J. McDermott | 2016-04-10 | 1 | -2/+2 |
| | | |||||
| * | Add PLA profile | P. J. McDermott | 2016-04-10 | 2 | -3/+20 |
| | | |||||
| * | Adjust printer retraction settings | P. J. McDermott | 2016-04-10 | 2 | -4/+4 |
| | | |||||
| * | Add start and stop G-Code | P. J. McDermott | 2016-04-10 | 2 | -4/+23 |
| | | |||||
| * | Use renamed printer profile | P. J. McDermott | 2016-04-10 | 1 | -2/+2 |
| | | |||||
| * | Rename printer profile | P. J. McDermott | 2016-04-10 | 2 | -2/+2 |
| | | |||||
| * | Switch to expert mode | P. J. McDermott | 2016-04-10 | 1 | -2/+6 |
| | | |||||
| * | Add printer settings | P. J. McDermott | 2016-04-10 | 4 | -1/+167 |
| | | |||||
| * | Initial commit | P. J. McDermott | 2016-04-10 | 1 | -0/+6 |
 |
index : dotfiles/slic3r.git | |
| Slic3r configuration | P. J. McDermott |
| summaryrefslogtreecommitdiffstats |