dotfiles/slic3r.git - Slic3r configuration

	Commit message (Collapse)	Author	Age	Files	Lines
*	Base: Reduce speeds to 20	Patrick McDermott	2019-10-19	1	-10/+10
\|
*	Base: Reduce speeds to 40	Patrick McDermott	2019-10-19	1	-8/+8
\|
*	Base: Reduce top, bottom, and bridge speeds to 60	Patrick McDermott	2019-10-19	1	-5/+5
\|
*	Base: Reduce top, bottom, and bridge speeds to 80	Patrick McDermott	2019-10-19	1	-4/+4
\|
*	Revert "Base: Slow down first layer"	Patrick McDermott	2019-10-19	1	-2/+2
\| \| \| \|	This reverts commit 2d7ef32ac94331723b33a9be93ea1ff5a71f8085.
*	Base: Slow down first layer	Patrick McDermott	2019-10-19	1	-2/+2
\|
*	Base: Set bridge speed to 100	Patrick McDermott	2019-10-19	1	-2/+2
\|
*	Base: Raise perimeter and solid fill speeds to 100	Patrick McDermott	2019-10-19	1	-6/+6
\|
*	Base: Decrease fill density to 10%	Patrick McDermott	2019-10-19	1	-2/+2
\|
*	Base: Disable ineffective infill combination	Patrick McDermott	2019-10-19	1	-2/+2
\| \| \| \|	Doesn't work when infill_every_layers * layer_height == nozzle_diameter.
*	Revert "Base: Reduce layer height to 0.2 mm"	Patrick McDermott	2019-10-18	1	-3/+3
\| \| \| \| \| \| \| \|	This reverts commit ab84e54274cf87f575ff1436b064ac52df3f9ad9. The higher number of perimeter layers and lower number of infill layers almost balance each other out in print time. Layer seams are similar as well; if anything, the 0.2-mm seams protrude more.
*	Base: Reduce layer height to 0.2 mm	Patrick McDermott	2019-10-18	1	-3/+3
\| \| \| \|	Now infill_every_layers is actually effective.
*	Base: Raise perimeter and top infill speeds to 80	Patrick McDermott	2019-10-18	1	-5/+5
\|
*	Base: Increase infill to 20%	P. J. McDermott	2019-02-16	1	-2/+2
\|
*	Revert "Base: Increase solid infill speed"	P. J. McDermott	2019-02-16	1	-2/+2
\| \| \| \| \| \| \|	This reverts commit 2951372658017c61012b7a845abd0dbeda8bc0ee. Slic3r uses this speed for the bottom solid infill, so at this speed there's insufficient extrusion.
*	Base: Increase solid infill speed	P. J. McDermott	2019-02-16	1	-2/+2
\|
*	Revert "Revert "Base: Reduce infill overlap to 0""	P. J. McDermott	2019-02-15	1	-2/+2
\| \| \| \|	This reverts commit 845c4ac12e94c49760f8e9519ab469b816576a12.
*	Revert "Base: Reduce infill overlap to 0"	P. J. McDermott	2019-02-15	1	-2/+2
\| \| \| \|	This reverts commit 8c298d81d0463734718be995d9bd838be4f21d67.
*	Base: Reduce infill overlap to 0	P. J. McDermott	2019-02-15	1	-2/+2
\|
*	Base: Slow down perimeters, speed up infill	P. J. McDermott	2019-02-14	1	-8/+8
\|
*	Base: Infill everywhere	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Revert "Revert "Revert "Base: Increase speeds"""	P. J. McDermott	2019-02-14	1	-11/+11
\| \| \| \|	This reverts commit 0788865c4bf387d862598a0cb5d9fa1d41014f7a.
*	Revert "Revert "Base: Increase speeds""	P. J. McDermott	2019-02-14	1	-11/+11
\| \| \| \|	This reverts commit 184eb929444cd45bc49d6eaf33e00be13a89047d.
*	Revert "Base: Increase minimum skirt length"	P. J. McDermott	2019-02-14	1	-1/+1
\| \| \| \|	This reverts commit a34dda7501fb006879f19b1ed9b76fb1f8338b52.
*	Revert "Base: Increase speeds"	P. J. McDermott	2019-02-14	1	-11/+11
\| \| \| \|	This reverts commit 305f7215ca937b31a6f1ec54ae928df138196834.
*	Base: Increase speeds	P. J. McDermott	2019-02-14	1	-11/+11
\|
*	Base: Reduce solid infill threshold area	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Increase minimum skirt length	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Reduce infill/perimeters overlap	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Run 4 threads	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Combine infill and only infill where needed	P. J. McDermott	2019-02-14	1	-3/+3
\|
*	Base: Increase speeds	P. J. McDermott	2019-02-14	1	-8/+8
\|
*	TAZ 6, SE v2.1, eSUN PLA; Base: Lift on retract, increase travel speed	P. J. McDermott	2019-02-14	1	-2/+2
\|
*	Base: Increase travel speed	P. J. McDermott	2019-02-13	1	-2/+2
\|
*	Base: New print preset, based on SFF-8201 HA	P. J. McDermott	2019-02-13	1	-0/+86